Carbon capture and storage (CCS) (or carbon capture and sequestration or carbon control and sequestration) is the process of capturing waste carbon dioxide (CO2) from large point sources, such as a biomass power plant or a cement factory, transporting it to a storage site, and depositing it where it will not enter the atmosphere, normally an underground geological formation The aim is to prevent the release of large quantities of CO2 into the atmosphere from heavy industry It is a potential means of mitigating the contribution to global warming and ocean acidification of carbon dioxide emissions from industry and heating Although CO2 has been injected into geological formations for several decades for various purposes, including enhanced oil recovery, the long term storage of CO2 is a relatively new concept ‘CCS’ can also be used to describe the scrubbing of CO2 from ambient air as a climate engineering technique CCS applied to a modern conventional power plant could reduce CO2 emissions to the atmosphere by approximately 80–90% compared to a plant without CCS.Carbon dioxide can be captured out of air or power plant flue gas using adsorption (or carbon scrubbing), membrane gas separation, or adsorption technologies Amines are the leading carbon scrubbing technology However capturing and compressing CO2 and other system costs are estimated to increase the cost per watt-hour energy produced by 21–91% for fossil fuel power plants; and applying the technology to existing plants would be more expensive, especially if they are far from a sequestration site As of 2019 there are 17 operating CCS projects in the world, capturing 31.5Mt of CO2 per year, of which 3.7 is stored geologically.It is possible for CCS, when combined with biomass, to result in net negative emissions A trial of bio-energy with carbon capture and storage (BECCS) at a wood-fired unit in Drax power station in the UK started in 2019: if successful this could remove a tiny amount of CO2 from the atmosphere.Storage of the CO2 is envisaged either in deep geological formations, or in the form of mineral carbonates Deep ocean storage is not currently considered feasible due to the associated effect of ocean acidification Geological formations are currently considered the most promising sequestration sites The National Energy Technology Laboratory (NETL) reported that North America has enough storage capacity for more than 900 years worth of carbon dioxide at current production rates A general problem is that long term predictions about submarine or underground storage security are very difficult and uncertain, and there is still the risk that CO2 might leak into the atmosphere.CCS is closely related to pyrogenic carbon capture and storage (PyCCS) == Capture == Capturing CO2 is most effective at point sources, such as large fossil fuel or biomass energy facilities, industries with major CO2 emissions, natural gas processing, synthetic fuel plants and fossil fuel-based hydrogen production plants Extracting CO2 from air is also possible, although the far lower concentration of CO2 in air compared to combustion sources presents significant engineering challenges.Organisms that produce ethanol by fermentation generate cool, essentially pure CO2 that can be pumped

underground Fermentation produces slightly less CO2 than ethanol by weight Impurities in CO2 streams, like sulfurs and water, could have a significant effect on their phase behaviour and could pose a significant threat of increased corrosion of pipeline and well materials In instances where CO2 impurities exist, especially with air capture, a scrubbing separation process would be needed to initially clean the flue gas According to the Wallula Energy Resource Center in Washington state, by gasifying coal, it is possible to capture approximately 65% of carbon dioxide embedded in it and sequester it in a solid form.Broadly, three different configurations of technologies for capture exist: post-combustion, pre-combustion, and oxyfuel combustion: In post combustion capture, the CO2 is removed after combustion of the fossil fuel—this is the scheme that would be applied to fossil-fuel burning power plants Here, carbon dioxide is captured from flue gases at power stations or other large point sources The technology is well understood and is currently used in other industrial applications, although not at the same scale as might be required in a commercial scale power station Post combustion capture is most popular in research because existing fossil fuel power plants can be retrofitted to include CCS technology in this configuration The technology for pre-combustion is widely applied in fertilizer, chemical, gaseous fuel (H2, CH4), and power production In these cases, the fossil fuel is partially oxidized, for instance in a gasifier The CO from the resulting syngas (CO and H2) reacts with added steam (H2O) and is shifted into CO2 and H2 The resulting CO2 can be captured from a relatively pure exhaust stream The H2 can now be used as fuel; the carbon dioxide is removed before combustion takes place There are several advantages and disadvantages when compared to conventional post combustion carbon dioxide capture The CO2 is removed after combustion of fossil fuels, but before the flue gas is expanded to atmospheric pressure This scheme is applied to new fossil fuel burning power plants, or to existing plants where re-powering is an option The capture before expansion, i.e. from pressurized gas, is standard in almost all industrial CO2 capture processes, at the same scale as required for power plants In oxy-fuel combustion the fuel is burned in oxygen instead of air To limit the resulting flame temperatures to levels common during conventional combustion, cooled flue gas is recirculated and injected into the combustion chamber The flue gas consists of mainly carbon dioxide and water vapour, the latter of which is condensed through cooling The result is an almost pure carbon dioxide stream that can be transported to the sequestration site and stored Power plant processes based on oxyfuel combustion are sometimes referred to as “zero emission” cycles, because the CO2 stored is not a fraction removed from the flue gas stream (as in the cases of pre- and post-combustion capture) but the flue gas stream itself A certain fraction of the CO2 generated during combustion will inevitably end up in the condensed water To warrant the label “zero emission” the water would thus have to be treated or disposed of appropriately The technique is promising, but the initial air separation step demands a lot of energy

=== CO2 separation technologies === Carbon dioxide can be separated out of air or flue gas with absorption, adsorption, or membrane gas separation technologies Absorption, or carbon scrubbing, with amines is currently the dominant capture technology Membrane and adsorption technologies are still in the developmental research stages, initiating primary pilot plants in the near future Metal–organic frameworks (MOFs) are a novel class of materials that offer promise for carbon capture using adsorption technologies.Carbon dioxide adsorbs to a MOF through physisorption or chemisorption based on the porosity and selectivity of the MOF leaving behind a Greenhouse gas poor gas stream that is more environmentally friendly The carbon dioxide is then stripped off the MOF using temperature swing adsorption (TSA) or pressure swing adsorption (PSA) so the MOF can be reused Adsorbents and absorbents require regeneration steps where the CO2 is removed from the sorbent or solution that collected it out of the flue gas in order for the sorbent or solution to be reused Monoethanolamine (MEA) solutions, the leading amine for capturing CO2, have a heat capacity between 3–4 J/g K since they are mostly water Higher heat capacities add to the energy penalty in the solvent regeneration step Thus, to optimize a MOF for carbon capture, low heat capacities and heats of adsorption are desired Additionally, high working capacity and high selectivity are desirable in order to capture as much CO2 as possible from the flue gas However, there is an energy trade off with selectivity and energy expenditure As the amount of CO2 captured increases, the energy, and therefore cost, required to regenerate increases A large drawback of using MOFs for CCS is the limitations imposed by their chemical and thermal stability Current research is looking to optimize MOF properties for CCS, but it has proven difficult to find these optimizations that also result in a stable MOF Metal reservoirs are also a limiting factor to the potential success of MOFs.About two thirds of the total cost of CCS is attributed to capture, making it limit the wide-scale deployment of CCS technologies To optimize a CO2 capture process would significantly increase the feasibility of CCS since the transport and storage steps of CCS are rather mature technologies.An alternate method under development is chemical looping combustion (CLC) Chemical looping uses a metal oxide as a solid oxygen carrier Metal oxide particles react with a solid, liquid or gaseous fuel in a fluidized bed combustor, producing solid metal particles and a mixture of carbon dioxide and water vapor The water vapor is condensed, leaving pure carbon dioxide, which can then be sequestered The solid metal particles are circulated to another fluidized bed where they react with air, producing heat and regenerating metal oxide particles that are recirculated to the fluidized bed combustor A variant of chemical looping is calcium looping, which uses the alternating carbonation and then calcination of a calcium oxide based carrier as a means of capturing CO2 === Direct air capture === Direct air capture refers to the process of removing CO2 directly from the ambient air (as opposed to from point sources)

Combining direct air capture with carbon storage could act as a carbon dioxide removal technology and as such would constitute a form of climate engineering if deployed at large scale A few engineering proposals have been made for such direct air capture, but work in this area is still in its infancy A pilot plant has operated in British Columbia, Canada since 2015 An economic study of this plant in 2018 estimated the cost at US$94–$232 per tonne of atmospheric CO2 removed This estimate has decreased compared to a 2011 study that estimated that direct air capture would cost $600 per tonne Depending on the circumstances DAC is considered to cost between $200–1000/ton CO2.Among the specific chemical processes that are being explored, three stand out: causticization with alkali and alkali-earth hydroxides, carbonation, and organic−inorganic hybrid sorbents consisting of amines supported in porous adsorbents Given that CO2 in the atmosphere is highly diluted compared to point-source CO2 capture, capture costs are estimated to be higher Once costs and incentives for climate change mitigation rise higher later this century, however, they might become attractive for dealing with emissions from diffuse sources such as automobiles and aircraft Global Research Technologies demonstrated a pre-prototype of air capture technology in 2007 == Transport == After capture, the CO2 would have to be transported to suitable storage sites This would most likely be done by pipeline, which is generally the cheapest form of transport for large volume of CO2 In 2008, there were approximately 5,800 km of CO2 pipelines in the United States, used to transport CO2 to oil production fields where it is then injected into older fields to extract oil The injection of CO2 to produce oil is called enhanced oil recovery In addition, there are several pilot programs in various stages to test the long-term storage of CO2 in non-oil producing geologic formations According to the Congressional Research Service, “There are important unanswered questions about pipeline network requirements, economic regulation, utility cost recovery, regulatory classification of CO2 itself, and pipeline safety Furthermore, because CO2 pipelines for enhanced oil recovery are already in use today, policy decisions affecting CO2 pipelines take on an urgency that is unrecognized by many Federal classification of CO2 as both a commodity (by the Bureau of Land Management) and as a pollutant (by the Environmental Protection Agency) could potentially create an immediate conflict which may need to be addressed not only for the sake of future CCS implementation, but also to ensure consistency of future CCS with CO2 pipeline operations today.”Ships could also be utilized for transport where pipelines are not feasible These methods are currently used for transporting CO2 for other applications == Sequestration == Various forms have been conceived for permanent storage of CO2 These forms include gaseous storage in various deep geological formations (including saline

formations and exhausted gas fields), and solid storage by reaction of CO2 with metal oxides to produce stable carbonates === Geological storage === Also known as geo-sequestration, this method involves injecting carbon dioxide, generally in supercritical form, directly into underground geological formations Oil fields, gas fields, saline formations, unmineable coal seams, and saline-filled basalt formations have been suggested as storage sites Various physical (e.g., highly impermeable caprock) and geochemical trapping mechanisms would prevent the CO2 from escaping to the surface.CO2 is sometimes injected into declining oil fields to increase oil recovery Approximately 30 to 50 million metric tonnes of CO2 are injected annually in the United States into declining oil fields This option is attractive because the geology of hydrocarbon reservoirs is generally well understood and storage costs may be partly offset by the sale of additional oil that is recovered Disadvantages of old oil fields are their geographic distribution and their limited capacity, as well as the fact that subsequent burning of the additional oil recovered will offset much or all of the reduction in CO2 emissions.Unmineable coal seams can be used to store CO2 because the CO2 molecules attach to the surface of coal The technical feasibility, however, depends on the permeability of the coal bed In the process of absorption the coal releases previously absorbed methane, and the methane can be recovered (enhanced coal bed methane recovery) The sale of the methane can be used to offset a portion of the cost of the CO2 storage Burning the resultant methane, however, would negate some of the benefit of sequestering the original CO2 Saline formations contain highly mineralized brines, and have so far been considered of no benefit to humans Saline aquifers have been used for storage of chemical waste in a few cases The main advantage of saline aquifers is their large potential storage volume and their common occurrence The major disadvantage of saline aquifers is that relatively little is known about them, especially compared to oil fields To keep the cost of storage acceptable, the geophysical exploration may be limited, resulting in larger uncertainty about the aquifer structure Unlike storage in oil fields or coal beds, no side product will offset the storage cost Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage Current research shows, however, that trapping mechanisms such as structural trapping, residual trapping, solubility trapping and mineral trapping could immobilize the CO2 underground and reduce the risk of leakage ==== Carbon Dioxide Storage with Carbon Dioxide Degrading Algae or Bacterium ==== An alternative to geochemical injection would instead be to physically store carbon dioxide in containers with algae or bacteria that could degrade the carbon dioxide It would ultimately be ideal to exploit the carbon dioxide metabolizing bacterium Clostridium thermocellum in such theoretical CO2 storage containers Using this bacteria would prevent overpressurization of such theoretical carbon dioxide storage containers ==== Enhanced oil recovery ==== Enhanced oil recovery (EOR) is a generic term

for techniques used to increase the amount of crude oil that can be extracted from an oil field In carbon capture and sequestration enhanced oil recovery (CCS EOR), carbon dioxide is injected into an oil field to recover oil that is often never recovered using more traditional methods Crude oil development and production in U.S oil reservoirs can include up to three distinct phases: primary, secondary, and tertiary (or enhanced) recovery During primary recovery only about 10 percent of a reservoir’s original oil in place is typically produced Secondary recovery techniques extend a field’s productive life generally by injecting water or gas to displace oil and drive it to a production wellbore, resulting in the recovery of 20 to 40 percent of the original oil in place However, with much of the easy-to-produce oil already recovered from U.S. oil fields, producers have attempted several tertiary, or enhanced oil recovery, techniques that offer prospects for ultimately producing 30 to 60 percent, or more, of the reservoir’s original oil in place.An example of a project that will use CCS EOR is the Kemper Project in Mississippi Due to the Kemper Project’s close proximity to oil fields, the carbon dioxide byproduct from producing electricity will be transported to the neighboring oil fields for enhanced oil recovery === Ocean storage === ==== Framework Convention On Climate Change ==== Held in 1992, the results from this climate convention are the most widely agreed upon for addressing the problem of climate change and the use of sinks of greenhouse gases Ocean storage of CO2 has been pointed out as a viable option of mitigating the levels of carbon dioxide in the atmosphere However, the convention also states that there should be precautionary measures taken to mitigate any detriments to the environment Therefore, with this convention, ocean storage may prove to be a way to store carbon dioxide efficiently, especially in places where it is cost effective such as Norway ==== London Convention ==== Taken place in 1972 with more than 70 members, the result of the London Convention is that it prohibits all ocean dumping without the direct approval of a national authority In 1991, an addendum also prohibited the dumping of all radioactive and industrial waste, making it unclear and debated to today whether or not carbon dioxide falls under industrial waste The London Convention also applies to sea-faring vessels such as ships, planes, and offshore drilling platforms If these types of vessels want to dump carbon dioxide into the ocean, they must get permission from their respective national authority.The 1996 Protocol to the London Convention went even further by prohibiting carbon dioxide storage that comes from sea-based storage In 1997, the Joint Group of Experts on the Scientific Aspects of Marine environmental Protection stated that until there was 2/3 majority vote, any dumping of carbon dioxide from ships was in direct violation of the London Convention ==== OSPAR Convention ==== Also occurring in 1992, this convention was set up to protect the North East Atlantic Ocean

The convention was more certain in its results from the meeting The first is that it prohibited carbon dioxide from going to a storage site through a petroleum platform and also prohibited transport by ship It did however, allow transport of carbon dioxide through a pipeline from land to a site that did not require the use of a platform used for gas exploration.In the past, it was suggested that CO2 could be stored in the oceans, but this would only exacerbate ocean acidification and has been made illegal under specific regulations Ocean storage is no longer considered feasible === Mineral storage === In this process, CO2 is exothermically reacted with available metal oxides, which in turn produces stable carbonates (e.g. calcite, magnesite) This process occurs naturally over many years and is responsible for a great amount of surface limestone The idea of using olivine has been promoted by the geochemist Prof. Schuiling The reaction rate can be made faster, for example, with a catalyst or by reacting at higher temperatures and/or pressures, or by pre-treatment of the minerals, although this method can require additional energy The IPCC estimates that a power plant equipped with CCS using mineral storage will need 60–180% more energy than a power plant without CCS.The economics of mineral carbonation at scale are now being tested in a world-first pilot plant project based in Newcastle, Australia New techniques for mineral activation and reaction have been developed the GreenMag Group and the University of Newcastle and funded by the New South Wales and Australian Governments to be operational by 2013.In 2009 it was reported that scientists had mapped 6,000 square miles (16,000 km2) of rock formations in the U.S. that could be used to store 500 years’ worth of U.S. carbon dioxide emissions A study on mineral sequestration in the US states: Carbon sequestration by reacting naturally occurring Mg and Ca containing minerals with CO2 to form carbonates has many unique advantages Most notabl[e] is the fact that carbonates have a lower energy state than CO2, which is why mineral carbonation is thermodynamically favorable and occurs naturally (e.g., the weathering of rock over geologic time periods) Secondly, the raw materials such as magnesium based minerals are abundant Finally, the produced carbonates are unarguably stable and thus re-release of CO2 into the atmosphere is not an issue However, conventional carbonation pathways are slow under ambient temperatures and pressures The significant challenge being addressed by this effort is to identify an industrially and environmentally viable carbonation route that will allow mineral sequestration to be implemented with acceptable economics The following table lists principal metal oxides of Earth’s Crust Theoretically, up to 22% of this mineral mass is able to form carbonates Ultramafic mine tailings are a readily available source of fine-grained metal oxides that can act as artificial carbon sinks to reduce net greenhouse gas emissions in the mining industry Accelerating passive CO2 sequestration via mineral carbonation may be achieved through microbial processes that enhance mineral dissolution and carbonate precipitation === Energy requirements === The energy requirements of sequestration processes

may be significant In one paper, sequestration consumed 25% of the plant’s rated 600-megawatt output capacity After adding CO2 capture and compression, the capacity of the coal-fired power plant is reduced to 457 MW == Leakage == A major concern with CCS is whether leakage of stored CO2 will compromise CCS as a climate change mitigation option For well-selected, designed and managed geological storage sites, IPCC estimates that risks are comparable to those associated with current hydrocarbon activity However, this finding is contested due to a lack of experience in such long term storage CO2 could be trapped for millions of years, and although some leakage occurs upwards through the soil, well selected storage sites are likely to retain over 99% of the injected CO2 over 1000 years Leakage through the injection pipe is a greater risk.Although the injection pipe is usually protected with non-return valves to prevent release on a power outage, there is still a risk that the pipe itself could tear and leak due to the pressure The Berkel en Rodenrijs incident in December 2008 was an example, where a modest release of CO2 from a pipeline under a bridge resulted in the deaths of some ducks sheltering there In order to measure accidental carbon releases more accurately and decrease the risk of fatalities through this type of leakage, the implementation of CO2 alert meters around the project perimeter has been proposed Malfunction of a carbon dioxide industrial fire suppression system in a large warehouse released CO2 and 14 citizens collapsed on the nearby public road A release of CO2 from a salt mine killed a person at distance of 300 meters.In 1986 a large leakage of naturally sequestered CO2 rose from Lake Nyos in Cameroon and asphyxiated 1,700 people While the carbon had been sequestered naturally, some point to the event as evidence for the potentially catastrophic effects of sequestering carbon artificially The Lake Nyos disaster resulted from a volcanic event, which very suddenly released as much as a cubic kilometre of CO2 gas from a pool of naturally occurring CO2 under the lake in a deep narrow valley The location of this pool of CO2 is not a place where man can inject or store CO2, and this pool was not known about nor monitored until after the occurrence of the natural disaster For ocean storage, the retention of CO2 would depend on the depth The IPCC estimates 30–85% of the sequestered carbon dioxide would be retained after 500 years for depths 1000–3000 m Mineral storage is not regarded as having any risks of leakage The IPCC recommends that limits be set to the amount of leakage that can take place This might rule out deep ocean storage as an option At the conditions of the deeper oceans, (about 400 bar or 40 MPa, 280 K) water–CO2(l) mixing is very low (where carbonate formation/acidification is the rate limiting step), but the formation of water–CO2 hydrates, a kind of solid water cage that surrounds the CO2, is favorable To further investigate the safety of CO2 sequestration, Norway’s Sleipner gas field can be studied, as it is the oldest plant that stores CO2 on an industrial scale According to an environmental assessment of the gas field which was conducted after ten

years of operation, the author affirmed that geosequestration of CO2 was the most definite form of permanent geological storage of CO2: Available geological information shows absence of major tectonic events after the deposition of the Utsira formation [saline reservoir] This implies that the geological environment is tectonically stable and a site suitable for carbon dioxide storage The solubility trapping [is] the most permanent and secure form of geological storage In March 2009 StatoilHydro issued a study showing the slow spread of CO2 in the formation after more than 10 years operation.Phase I of the Weyburn-Midale Carbon Dioxide Project in Weyburn, Saskatchewan, Canada has determined that the likelihood of stored CO2 release is less than one percent in 5,000 years A January 2011 report, however, claimed evidence of leakage in land above that project This report was strongly refuted by the IEAGHG Weyburn-Midale CO2 Monitoring and Storage Project, which issued an eight-page analysis of the study, claiming that it showed no evidence of leakage from the reservoir.The liability of potential leak(s) is one of the largest barriers to large-scale CCS To assess and reduce such liability, the leakage of stored gasses, particularly carbon dioxide, into the atmosphere may be detected via atmospheric gas monitoring, and can be quantified directly via the eddy covariance flux measurements == Monitoring geological sequestration sites == In order to detect carbon dioxide leaks and the effectiveness of geological sequestration sites, different monitoring techniques can be employed to verify that the sequestered carbon stays trapped below the surface in the intended reservoir Leakage due to injection at improper locations or conditions could result in carbon dioxide being released back into the atmosphere It is important to be able to detect leaks with enough warning to put a stop to it, and to be able to quantify the amount of carbon that has leaked for purposes such as cap and trade policies, evaluation of environmental impact of leaked carbon, as well as accounting for the total loss and cost of the process To quantify the amount of carbon dioxide released, should a leak occur, or to closely watch stored CO2, there are several monitoring methods that can be done at both the surface and subsurface levels === Subsurface monitoring === In subsurface monitoring, there are direct and indirect methods to determine the amount of CO2 in the reservoir A direct method would be drilling deep enough to collect a fluid sample This drilling can be difficult and expensive due to the physical properties of the rock It also only provides data at a specific location Indirect methods would be to send sound or electromagnetic waves down to the reservoir where it is then reflected back up to be interpreted This approach is also expensive but it provides data over a much larger region; it does however lack precision Both direct and indirect monitoring can be done intermittently or continuously === Seismic monitoring === Seismic monitoring is a type of indirect subsurface monitoring It is done by creating vibrational waves either at the surface using a vibroseis truck, or inside a well using spinning eccentric mass

These vibrational waves then propagate through the geological layers and reflect back creating patterns that are read and interpreted by seismometers It can identify migration pathways of the CO2 plume Two examples of monitoring geological sequestration sites using seismic monitoring are the Sleipner sequestration project and the Frio CO2 Injection test Although this method can confirm the presence of CO2 in a given region, it cannot determine the specifics of the environment or concentration of CO2 === Surface monitoring === Eddy covariance is a surface monitoring technique that measures the flux of CO2 from the ground’s surface It involves measuring CO2 concentrations as well as vertical wind velocities using an anemometer This provides a measure of the total vertical flux of CO2 Eddy covariance towers could potentially detect leaks, however, the natural carbon cycle, such as photosynthesis and the respiration of plants, would have to be accounted for and a baseline CO2 cycle would have to be developed for the location of monitoring An example of Eddy covariance techniques used to monitor carbon sequestration sites is the Shallow Release test Another similar approach is utilizing accumulation chambers These chambers are sealed to the ground with an inlet and outlet flow stream connected to a gas analyzer This also measures the vertical flux of CO2 The disadvantage of accumulation chambers is its inability to monitor a large region which is necessary in detecting CO2 leaks over the entire sequestration site === InSAR monitoring === InSAR monitoring is another type of surface monitoring It involves a satellite sending signals down to the Earth’s surface where it is reflected back to the satellite’s receiver From this, the satellite is able to measure the distance to that point In CCS, the injection of CO2 in deep sublayers of geological sites creates high pressures These high pressured, fluid filled layers affect those above and below it resulting in a change of the surface landscape In areas of stored CO2, the ground’s surface often rises due to the high pressures originating in the deep subsurface layers These changes in elevation of the Earth’s surface corresponds to a change in the distance from the inSAR satellite which is then detectable and measurable == Carbon capture and utilization (CCU) == Carbon Capture and Utilization (CCU) differs from CCS as CCU does not result in geological storage of carbon dioxide Carbon capture and utilization may offer a response to the global challenge of significantly reducing greenhouse gas emissions from major stationary (industrial) emitters CCU aims to use the carbon dioxide produced to make other substances (e.g. plastics, concrete, biofuel) such that the whole process is carbon neutral Technologies under development, such as Bio CCS Algal Synthesis, utilises pre-smokestack CO2 (such as from a power station) as a useful feedstock input to the production of oil-rich algae in solar membranes to produce oil for plastics and transport fuel (including aviation fuel), and nutritious stock-feed for farm animal production The CO2 and other captured greenhouse gases are injected into the membranes containing

waste water and select strains of algae causing, together with sunlight or UV light, an oil rich biomass that doubles in mass every 24 hours The Bio CCS Algal Synthesis process is based on earth science photosynthesis: the technology is entirely retrofittable and collocated with the emitter, and the capital outlays may offer a return upon investment due to the high value commodities produced (oil for plastics, fuel and feed) Bio CCS Algal Synthesis test facilities were being trialed at Australia’s three largest coal-fired power stations (Tarong, Queensland; Eraring, NSW; Loy Yang, Victoria) using piped pre-emission smokestack CO2 (and other greenhouse gases) as feedstock to grow oil-rich algal biomass in enclosed membranes for the production of plastics, transport fuel and nutritious animal feed Another potentially useful way of dealing with industrial sources of CO2 is to convert it into hydrocarbons where it can be stored or reused as fuel or to make plastics There are a number of projects investigating this possibility For instance, several Carbon dioxide scrubbing variants based on potassium carbonate allow capture of carbon dioxide which can later be used to create liquid fuels, even though this process requires a substantial energy input The creation of fuel from atmospheric CO2 does not result in carbon dioxide removal as carbon dioxide is re-released when the fuel is burned For this reason, synfuels do not represent a climate engineering technique, but still represent a potentially useful source of net-zero-carbon fuel Other uses are the production of stable carbonates from silicates (e.g. olivine produces magnesium carbonate) These processes are still under research and development === Single step methods: methanol === A proven process to produce a hydrocarbon is to make methanol Methanol is easily synthesized from CO2 and H2 Based on this fact the idea of a methanol economy was born === Single step methods: hydrocarbons === At the department of Industrial Chemistry and Engineering of Materials at the University of Messina, Italy, there is a project to develop a system which works like a fuel-cell in reverse, whereby a catalyst is used that enables sunlight to split water into hydrogen ions and oxygen gas The ions cross a membrane where they react with the CO2 to create hydrocarbons === Two step methods === If CO2 is heated to 2400 °C, it splits into carbon monoxide (CO) and oxygen The Fischer-Tropsch process can then be used to convert the CO into hydrocarbons The required temperature can be achieved by using a chamber containing a mirror to focus sunlight on the gas Rival teams are developing such chambers, at Solarec and at Sandia National Laboratories, both based in New Mexico According to Sandia these chambers could provide enough fuel to power 100% of domestic vehicles using 5800 km2; unlike biofuels this would not take fertile land away from crops but would be land that is not being used for anything else James May, the British TV presenter, visited a demonstration plant in a programme in his Big Ideas series

== Example CCS projects == === Industrial-scale projects === As of September 2017, the Global CCS Institute identified 37 large-scale CCS facilities in its 2017 Global Status of CCS report which is a net decrease of one project since its 2016 Global Status of CCS report 21 of these projects are in operation or in construction capturing more than 30 million tonnes of CO2 per annum For the most current information, see Large Scale CCS facilities on the Global CCS Institute’s website For information on EU projects see Zero Emissions Platform website Some of the most notable CCS large scale facilities include: ==== Terrell Natural Gas Processing Plant – US ==== Opening in 1972, the Terrell plant in Texas, USA is the oldest operating industrial CCS project as of 2017 CO2 is captured during gas processing and transported primarily via the Val Verde pipeline where it is eventually injected at Sharon Ridge oil field and other secondary sinks for use in enhanced oil recovery The facility captures an average of somewhere between 0.4 and 0.5 million tons of CO2 per annum ==== Enid Fertilizer – US ==== Beginning its operation in 1982, the facility owned by the Koch Nitrogen company is the second oldest large scale CCS facility still in operation The CO2 that is captured is a high purity byproduct of nitrogen fertilizer production The process is made economical by transporting the CO2 to oil fields for EOR ==== Shute Creek Gas Processing Facility – US ==== Around 7 million tonnes per annum of carbon dioxide are recovered from ExxonMobil’s Shute Creek gas processing plant in Wyoming, and transported by pipeline to various oil fields for enhanced oil recovery This project has been operational since 1986 and has the second largest CO2 capture capacity of any CCS facility in the world ==== Sleipner CO2 Injection – Norway ==== Sleipner is a fully operational offshore gas field with CO2 injection initiated in 1996 CO2 is separated from produced gas and reinjected in the Utsira saline aquifer (800–1000 m below ocean floor) above the hydrocarbon reservoir zones This aquifer extends much further north from the Sleipner facility at its southern extreme The large size of the reservoir accounts for why 600 billion tonnes of CO2 are expected to be stored, long after the Sleipner natural gas project has ended The Sleipner facility is the first project to inject its captured CO2 into a geological feature for the purpose of storage rather than economically compromising EOR ==== Century Plant – US ==== Occidental Petroleum, along with Sandridge

Energy, is operating a West Texas hydrocarbon gas processing plant and related pipeline infrastructure that provides CO2 for use in EOR With a total CO2 capture capacity of 8.4 Mt/a, the Century plant is the largest single industrial source CO2 capture facility in the world ==== Abu Dhabi – United Arab Emirates ==== After the success of their pilot plant operation in November 2011, the Abu Dhabi National Oil Company and Abu Dhabi Future Energy Company moved to create the first commercial CCS facility in the iron and steel industry The CO2, a byproduct of the iron making process, is transported via a 50 km pipeline to Abu Dhabi National Oil Company oil reserves for EOR The total carbon capture capacity of the facility is 800,000 tonnes per year ==== Petra Nova – US ==== The Petra Nova project is a billion dollar endeavor taken upon by NRG Energy and JX Nippon to partially retrofit their jointly owned W.A Parish coal-fired power plant with post-combustion carbon capture The plant, which is located in Thompsons, Texas (just outside of Houston), entered commercial service in 1977, and carbon capture began operation on January 10, 2017 The WA Parish unit 8 generates 240 MW and 90% of the CO2 (or 1.4 million tonnes) is captured per year The carbon dioxide captured (99% purity) from the power plant is compressed and piped about 82 miles to West Ranch Oil Field, Texas, where it will be used for enhanced oil recovery The field has a capacity of 60 million barrels of oil and has increased its production from 300 barrels per day to 4000 barrels daily This project is expected to run for at least another 20 years ==== Illinois Industrial – US ==== The Illinois Industrial Carbon Capture and Storage project is one of five currently operational facilities dedicated to geological CO2 storage The project received a 171 million dollar investment from the DOE and over 66 million dollars from the private sector The CO2 is a byproduct of the fermentation process of corn ethanol production and is stored 7000 feet underground in the Mt. Simon Sandstone saline aquifer The facility began its sequestration in April 2017 and has a carbon capture capacity of 1 Mt/a ==== In Salah CO2 Injection – Algeria ==== In Salah was a fully operational onshore gas field with CO2 injection CO2 was separated from produced gas and reinjected into the Krechba geologic formation at a depth of 1,900m Since 2004, about 3.8 Mt of CO2 has been captured during natural gas extraction and stored Injection was suspended in June 2011 due to concerns about the integrity of the seal, fractures and leakage into the caprock, and movement of CO2 outside of the Krechba hydrocarbon lease This project is notable for its pioneering in the use of Monitoring, Modeling, and Verification

(MMV) approaches === Developing projects === ==== Port of Rotterdam CCUS Backbone Initiative ==== Expected in 2021, the Port of Rotterdam CCUS Backbone Initiative aims to implement a “backbone” of shared CCS infrastructure for use by several businesses located around the Port of Rotterdam in Rotterdam, Netherlands The project, overseen by the Port of Rotterdam, natural gas company Gasunie, and the EBN, looks to capture and sequester 2 million tons of carbon dioxide per year starting in 2020 and increase this number in future years Although dependent on the participation of companies, the goal of this project is to greatly reduce the carbon footprint of the industrial sector of the Port of Rotterdam and establish a successful CCS infrastructure in the Netherlands following the recently canceled ROAD project Carbon dioxide captured from local chemical plants and refineries will both be sequestered in the North Sea seabed The possibility of a CCU initiative has also been considered, in which the captured carbon dioxide will be sold to horticultural firms, who will use it to speed up plant growth, as well as other industrial users === Alternative carbon capture methods === Although the majority of industrial carbon capture is done using post-combustion capture, several notable projects exist that utilize a variety of alternative capture methods Several smaller-scale pilot and demonstration plants have been constructed for research and testing using these methods, and a handful of proposed projects are in early development on an industrial scale Some of the most notable alternative carbon capture projects include: ==== Climeworks Direct Air Capture Plant and CarbFix2 Project ==== Climeworks opened the first commercial direct air capture plant in Zürich, Switzerland Their process involves capturing carbon dioxide directly from ambient air using a patented filter, isolating the captured carbon dioxide at high heat, and finally transporting it to a nearby greenhouse as a fertilizer The plant is built near a waste recovery facility that uses its excess heat to power the Climeworks plant.Climeworks is also working with Reykjavik Energy on the CarbFix2 project with funding from the European Union This project, located in Hellisheidi, Iceland, uses direct air capture technology to geologically store carbon dioxide by operating in conjunction with a large geothermal power plant Once carbon dioxide is captured using Climeworks’ filters, it is heated using heat from the geothermal plant and bound to water The geothermal plant then pumps the carbonated water into rock formations underground where the carbon dioxide reacts with basaltic bedrock and forms carbonite minerals ==== Duke Energy East Bend Station ==== Researchers at the Center for Applied Energy Research of the University of Kentucky are currently developing the algae-mediated conversion of coal-fired power plant flue gas to drop-in hydrocarbon fuels Through their work, these researchers have proven that the carbon dioxide within flue gas from coal-fired power plants can be captured using algae, which can be subsequently harvested

and utilized, e.g. as a feedstock for the production of drop-in hydrocarbon fuels === Canada === Canadian governments have committed $1.8 billion for the sake of funding different CCS projects over the span of the last decade The main governments and programs responsible for the funding are the federal government’s Clean Energy Fund, Alberta’s Carbon Capture and Storage fund, and the governments of Saskatchewan, British Columbia, and Nova Scotia Canada also works closely with the United States through the U.S.–Canada Clean Energy Dialogue launched by the Obama administration in 2009 ==== Alberta ==== Alberta has committed $170 million in 2013/2014 – and a total of $1.3 billion over 15 years – to fund two large-scale CCS projects that will help reduce CO2 emissions from tar sands refining ===== Alberta Carbon Trunk Line Project ===== The Alberta Carbon Trunk Line Project (ACTL), pioneered by Enhance Energy, consists of a 240 km pipeline that will collect carbon dioxide from various sources in Alberta and transport it to Clive oil fields for use in EOR (enhanced oil recovery) and permanent storage This CAN$1.2 billion project will be collecting carbon dioxide initially from the Redwater Fertilizer Facility and the Sturgeon Refinery The projections for ACTL make it the largest carbon capture and sequestration project in the world, with an estimated full capture capacity of 14.6 Mtpa Construction plans for the ACTL are in their final stages and capture and storage is expected to start sometime in 2019 ===== Quest Carbon Capture and Storage Project ===== The Quest Carbon Capture and Storage Project was developed by Shell for use in the Athabasca Oil Sands Project It is cited as being the world’s first commercial-scale CCS project Construction for the Quest Project began in 2012 and ended in 2015 The capture unit is located at the Scotford Upgrader in Alberta, Canada, where hydrogen is produced to upgrade bitumen from oil sands into synthetic crude oil The steam methane units that produce the hydrogen also emit CO2 as a byproduct The capture unit captures the CO2 from the steam methane unit using amine absorption technology, and the captured CO2 is then transported to Fort Saskatchewan where it is injected into a porous rock formation called the Basal Cambrian Sands for permanent sequestration Since beginning operation in 2015, the Quest Project has stored 3 Mt CO2 and will continue to store 1 Mtpa for as long as it is operational ==== British Columbia ==== British Columbia has been making strides with regards to reducing their carbon emissions The province implemented North America’s first large-scale carbon tax in 2008 An updated carbon tax in 2018 set the price at $35 per tonne of carbon dioxide equivalent emissions This tax will increase by $5 every year until it reaches $50 in 2021

Carbon taxes will make carbon capture and sequestration projects more financially feasible for the future ===== Fort Nelson Project ===== Spectra Energy’s Fort Nelson Project is the major carbon capture project occurring in British Columbia The source of CO2 will be from the Fort Nelson Natural Gas Processing Plant and will be transported 15 km via an onshore pipeline to middle Devonian carbonate rock that is between 6500 and 7000 feet deep The process will capture 2.2 Megatonne CO2 per year using pre-combustion amine capture technology Injections and MVA (Monitoring, Verification, and Accounting) Operations have already occurred in 2014 as part of a feasibility project, which was completed successfully The Fort Nelson Project is currently on the back burners as Spectra lacks the financial support to make it a reality at this time ==== Saskatchewan ==== ===== Boundary Dam Power Station Unit 3 Project ===== Boundary Dam Power Station, owned by SaskPower, is a coal fired station that was originally commissioned back in 1959 In 2010, SaskPower committed to retrofitting the lignite-powered Unit 3 with a carbon capture unit in order to reduce CO2 emissions The project was completed in 2014 The retrofit utilized a post-combusition amine absorption technology in order to capture the CO2 The captured CO2 was planned to be sold to Cenovus to be used for EOR in Weyburn field Any CO2 not used for EOR was planned to be used by the Aquistore project and stored in deep saline aquifers Many complications has kept Unit 3 and this project from being online as much as expected, but between August 2017 – August 2018, Unit 3 was online for 65% of every day on average Since the start of operation, the Boundary Dam project has captured over 1 Mt CO2 and has a nameplate capacity of capture of 1 Mtpa SaskPower does not intend to retrofit the rest of its units as they are mandated to be phased out by the government by 2024 The future of the one retrofitted unit at Boundary Dam Power Station is unclear ===== Great Plains Synfuel Plant and Weyburn-Midale Project ===== The Great Plains Synfuel Plant, owned by Dakota Gas, is a coal gasification operation that produces synthetic natural gas and various petrochemicals from coal The plant has been in operation since 1984, but carbon capture and storage did not start until 2000 In 2000, Dakota Gas retrofitted the plant with a carbon capture unit in order to sell the CO2 to Cenovus and Apache Energy, who intended to use the CO2 for enhanced oil recovery (EOR) in the Weyburn and Midale fields in Canada The Midale fields are injected with 0.4 Mtpa and the Weyburn fields are injected with 2.4 Mtpa for a total injection capacity of 2.8 Mtpa The Weyburn-Midale Carbon Dioxide Project (or IEA GHG Weyburn-Midale CO2 Monitoring and Storage Project), an international collaborative scientific study conducted between 2000–2011

also took place here, but injection has continued even after the study has concluded Since 2000, over 30 Mt CO2 has been injected and both the plant and EOR projects are still operational ==== Pilot projects ==== The Alberta Saline Aquifer Project (ASAP), Husky Upgrader and Ethanol Plant pilot, Heartland Area Redwater Project (HARP), Wabamun Area Sequestration Project (WASP), and Aquistore.Another Canadian initiative is the Integrated CO2 Network (ICO2N), a group of industry participants providing a framework for carbon capture and storage development in Canada Other Canadian organizations related to CCS include CCS 101, Carbon Management Canada, IPAC CO2, and the Canadian Clean Power Coalition === Netherlands === Developed in the Netherlands, an electrocatalysis by a copper complex helps reduce carbon dioxide to oxalic acid === Norway === In Norway, the CO2 Technology Centre (TCM) at Mongstad began construction in 2009, and completed in 2012 It includes two capture technology plants (one advanced amine and one chilled ammonia), both capturing fluegas from two sources This includes a gas-fired power plant and refinery cracker fluegas (similar to coal-fired power plant fluegas) In addition to this, the Mongstad site was also planned to have a full-scale CCS demonstration plant The project was delayed to 2014, 2018, and then indefinitely The project cost rose to US$985 million Then in October 2011, Aker Solutions’ wrote off its investment in Aker Clean Carbon, declaring the carbon sequestration market to be “dead”.On 1 October 2013 Norway asked Gassnova not to sign any contracts for Carbon capture and storage outside Mongstad.In 2015 Norway was reviewing feasibility studies and hoping to have a full-scale carbon capture demonstration project by 2020 === Poland === In Belchatów, Poland, a lignite-fired energy plant of more than 858 MW is planned to be in operation in 2013 === United States === In November 2008, the DOE awarded a $66.9 million eight-year grant to a research partnership headed by Montana State University to demonstrate that underground geologic formations “can store huge volumes of carbon dioxide economically, safely and permanently” Researchers under the Big Sky Regional Carbon Sequestration Project plan to inject up to one million tonnes of CO2 into sandstone beneath southwestern Wyoming.In the United States, four different synthetic fuel projects are moving forward, which have publicly announced plans to incorporate carbon capture and storage: American Clean Coal Fuels, in their Illinois Clean Fuels (ICF) project, is developing a 30,000-barrel (4,800 m3) per day biomass and coal to liquids project in Oakland, Illinois, which will market the CO2 created at the plant for enhanced oil recovery applications

By combining sequestration and biomass feedstocks, the ICF project will achieve dramatic reductions in the life-cycle carbon footprint of the fuels they produce If sufficient biomass is used, the plant should have the capability to go life-cycle carbon negative, meaning that effectively, for each gallon of their fuel that is used, carbon is pulled out of the air, and put into the ground Baard Energy, in their Ohio River Clean Fuels project, is developing a 53,000 bbl/d (8,400 m3/d) coal and biomass to liquids project, which has announced plans to market the plant’s CO2 for enhanced oil recovery Rentech is developing a 29,600-barrel (4,710 m3) per day coal and biomass to liquids plant in Natchez, Mississippi, which will market the plant’s CO2 for enhanced oil recovery The first phase of the project is expected in 2011 DKRW Energy is developing a 15,000–20,000-barrel (2,400–3,200 m3) per day coal to liquids plant in Medicine Bow, Wyoming, which will market its plant’s CO2 for enhanced oil recovery The project is expected to begin operation in 2013.In October 2009, the U.S. Department of Energy awarded grants to twelve Industrial Carbon Capture and Storage (ICCS) projects to conduct a Phase 1 feasibility study The DOE plans to select 3 to 4 of those projects to proceed into Phase 2, design and construction, with operational startup to occur by 2015 Battelle Memorial Institute, Pacific Northwest Division, Boise, Inc., and Fluor Corporation are studying a CCS system for capture and storage of CO2 emissions associated with the pulp and paper production industry The site of the study is the Boise White Paper L.L.C. paper mill located near the township of Wallula in Southeastern Washington State The plant generates approximately 1.2 MMT of CO2 annually from a set of three recovery boilers that are mainly fired with black liquor, a recycled byproduct formed during the pulping of wood for paper-making Fluor Corporation will design a customized version of their Econamine Plus carbon capture technology The Fluor system also will be designed to remove residual quantities of remnant air pollutants from stack gases as part of the CO2 capture process Battelle is leading preparation of an Environmental Information Volume (EIV) for the entire project, including geologic storage of the captured CO2 in deep flood basalt formations that exist in the greater region The EIV will describe the necessary site characterization work, sequestration system infrastructure, and monitoring program to support permanent sequestration of the CO2 captured at the plant.In addition to individual carbon capture and sequestration projects, there are a number of U.S. programs designed to research, develop, and deploy CCS technologies on a broad scale These include the National Energy Technology Laboratory’s (NETL) Carbon Sequestration Program, regional carbon sequestration partnerships and the Carbon Sequestration Leadership Forum (CSLF) ==== SECARB ==== In October 2007, the Bureau of Economic Geology at the University of Texas at Austin received a 10-year, $38 million subcontract to conduct the first intensively monitored long-term project in the United States studying the

feasibility of injecting a large volume of CO2 for underground storage The project is a research program of the Southeast Regional Carbon Sequestration Partnership (SECARB), funded by the National Energy Technology Laboratory of the U.S. Department of Energy (DOE) The SECARB partnership will demonstrate CO2 injection rate and storage capacity in the Tuscaloosa-Woodbine geologic system that stretches from Texas to Florida The region has the potential to store more than 200 billion tons of CO2 from major point sources in the region, equal to about 33 years of overall U.S. emissions at present rates Beginning in fall 2007, the project will inject CO2 at the rate of one million tons per year, for up to 1.5 years, into brine up to 10,000 feet (3,000 m) below the land surface near the Cranfield oil field, which lays about 15 miles (24 km) east of Natchez, Mississippi Experimental equipment will measure the ability of the subsurface to accept and retain CO2 The $1.4 billion FutureGen power generation and carbon sequestration demonstration project, announced in 2003 by President George W. Bush, was cancelled in 2015, due to delays and inability to raise required private funding ==== Kemper Project ==== The Kemper Project, is a natural gas-fired power plant under construction in Kemper County, Mississippi, which was originally planned as a coal-fired plant Mississippi Power, a subsidiary of Southern Company, began construction of the plant in 2010 The project was considered central to President Obama’s Climate Plan Had it become operational as a coal plant, the Kemper Project would have been a first-of-its-kind electricity plant to employ gasification and carbon capture technologies at this scale The emission target was to reduce CO2 to the same level an equivalent natural gas plant would produce However, in June 2017 the proponents – Southern Company and Mississippi Power – announced that they would only burn natural gas at the plant at this time.The plant experienced project management problems Construction was delayed and the scheduled opening was pushed back over two years, at a cost of $6.6 billion—three times original cost estimate According to a Sierra Club analysis, Kemper is the most expensive power plant ever built for the watts of electricity it will generate === United Kingdom === The government of the United Kingdom launched a first tender process for a CCS demonstration project in 2007 The project were to use post-combustion technology on coal-fired power generation at 300–400 megawatts or equivalent The project aimed to be operational by 2014 The Government announced in June 2008 that four companies had pre-qualified for the competition: BP Alternative Energy International Limited, EON UK Plc, Peel Power Limited and Scottish Power Generation Limited BP subsequently withdrew from the competition, claiming it could not find a power generator partner, and RWE npower sought a judicial review of the process after it did not qualify This first CCS tender was cancelled in late 2011 when government could not reach agreement with the ScottishPower/Shell/National Grid consortium on terms and cost, for the project

based on retrofitting the existing Longannet coal-fired power station in Scotland A second tender process was launched by government in 2012 as part of DECC’s CCS Commercialisation Programme and two bidders, namely the Shell Peterhead gas-fired power station CCS project and the White Rose CCS project based upon a new oxy-fuel coal-fired unit at Drax power station were selected in 2013 to proceed to a funded front-end engineering and design phase This second tender was cancelled in November 2015 following a government spending review at the time of the Chancellor’s Autumn Statement.Doosan Babcock has modified their Clean Combustion Test Facility (CCTF) in Renfrew, Scotland to create the largest Oxyfuel test facility currently in the world Oxyfuel firing on pulverized coal with recycled flue gas demonstrates the operation of a full scale 40 MW burner for use in coal-fired boilers Sponsors of the project include the UK Department for Business Enterprise and Regulatory Reform (BERR,) as well as a group of industrial sponsors and university partners comprising Scottish and Southern Energy (Prime Sponsor), E.ON UK PLC, Drax Power Limited, ScottishPower, EDF Energy, Dong Energy Generation, Air Products Plc (Sponsors), and Imperial College and University of Nottingham (University Partners).In 2009 UK firm 2Co Energy was awarded planning permission for a £5bn power station and carbon-capture-and-storage project at Hatfield, near Doncaster and £164m of EU funding Technology company Samsung agreed to take a 15% stake in the project It is planned to construct a 60 km (37 mi) pipeline from Stainforth, near Hatfield in South Yorkshire to Barmston in the East Riding of Yorkshire CO2 would then be stored in natural porous rock beneath the North Sea National Grid believes the project has the potential to reduce CO2 emissions from power stations across Yorkshire and the Humber by up to 90% and both the proposed White Rose CCS project at Drax Power Station in North Yorkshire and the proposed Don Valley Power Project at Hatfield could benefit from the scheme.In the Northeast of England, The Northeast of England Process Industry Cluster (NEPIC) of commodity chemical manufacturers are amongst the largest single point producers of carbon dioxide in the United Kingdom and they have created within NEPIC the Process Industry Carbon Capture and Storage Initiative (PICCSI) to study the possibility of a carbon capture and storage (CCS) solution being provided for the chemical and steel manufacturing industry on Teesside, as well as for any carbon based energy production This CCS technology option is being considered as a result of climate change regulations and the carbon taxation that could become a prohibitive cost for such energy intensive industries The Crown Estate is responsible for storage rights on the UK continental shelf and it has facilitated work on offshore carbon dioxide storage technical and commercial issues === China === Due to its large abundance in northern China, coal accounts for around 60% of the country’s energy consumption The majority of CO2 emissions in China come from either coal-fired power plants or coal-to-chemical processes (e.g. the production of synthetic ammonia, methanol, fertilizer, natural gas, and CTLs) According to the IEA, around 385 out of China’s 900 gigawatts of coal-fired power capacity

are near locations suitable for carbon dioxide storage In order to take advantage of these suitable storage sites (many of which are conducive to enhanced oil recovery) and reduce its carbon dioxide emissions, China has started to develop several CCS projects Three such facilities are already operational or in late stages of construction, but these projects draw CO2 from natural gas processing or petrochemical production At least eight more facilities are in early planning and development, most of which will capture emissions from power plants Almost all of these CCS projects, regardless of CO2 source, inject carbon dioxide for the purpose of EOR ==== CNPC Jilin Oil Field ==== China’s very first carbon capture project is the Jilin oil field in Songyuan, Jilin Province It started as a pilot EOR project in 2009, but has since developed into a commercial operation for the China National Petroleum Corporation (CNPC), with the final phase of development completed in 2018 The source of carbon dioxide is the nearby Changling gas field, from which natural gas with about 22.5% CO2 is extracted After separation at the natural gas processing plant, the carbon dioxide is transported to Jilin via pipeline and injected for a 37% enhancement in oil recovery at the low-permeability oil field At commercial capacity, the facility currently injects 0.6 MtCO2 per year, and it has injected a cumulative total of over 1.1 million tonnes over its lifetime ==== Sinopec Qilu Petrochemical CCS Project ==== The Sinopec Qilu Petrochemical Corporation is a large energy and chemical company currently developing a carbon capture unit whose first phase will be operational in 2019 The facility is located in Zibo City, Shandong Province, where there is a fertilizer plant that produces large amounts of carbon dioxide from coal/coke gasification The CO2 is to be captured by cryogenic distillation and will be transported via pipeline to the nearby Shengli oil field for enhanced oil recovery Construction of the first phase has already begun, and upon completion it will capture and inject 0.4 MtCO2 per year The Shengli oil field is also expected to be the destination for carbon dioxide captured from Sinopec’s Shengli power plant, although this facility is not expected to be operational until the 2020s ==== Yanchang Integrated CCS Project ==== Yanchang Petroleum is developing carbon capture facilities at two coal-to-chemicals plants in Yulin City, Shaanxi Province The first capture plant is capable of capturing 50,000 tonnes CO2 per year and was finished in 2012 Construction on the second plant started in 2014 and is expected to be finished in 2020, with a capacity of 360,000 tonnes captured per year This carbon dioxide will be transported to the Ordos Basin, one of the largest coal, oil, and gas-producing regions in China with a series of low- and ultra-low permeability oil reservoirs Lack of water in this area has limited the use of water flooding for EOR, so the injected

CO2 will support the development of increased oil production from the basin === Germany === The German industrial area of Schwarze Pumpe, about 4 kilometres (2.5 mi) south of the city of Spremberg, is home to the world’s first demonstration CCS coal plant, the Schwarze Pumpe power station The mini pilot plant is run by an Alstom-built oxy-fuel boiler and is also equipped with a flue gas cleaning facility to remove fly ash and sulphur dioxide The Swedish company Vattenfall AB invested some €70 million in the two-year project, which began operation September 9, 2008 The power plant, which is rated at 30 megawatts, is a pilot project to serve as a prototype for future full-scale power plants 240 tonnes a day of CO2 are being trucked 350 kilometers (220 mi) where it will be injected into an empty gas field Germany’s BUND group called it a “fig leaf” For each tonne of coal burned, 3.6 tonnes of carbon dioxide is produced The CCS program at Schwarze Pumpe ended in 2014 due to inviable costs and energy use.German utility RWE operates a pilot-scale CO2 scrubber at the lignite-fired Niederaußem power station built in cooperation with BASF (supplier of detergent) and Linde engineering.In Jänschwalde, Germany, a plan is in the works for an Oxyfuel boiler, rated at 650 thermal MW (around 250 electric MW), which is about 20 times more than Vattenfall’s 30 MW pilot plant under construction, and compares to today’s largest Oxyfuel test rigs of 0.5 MW Post-combustion capture technology will also be demonstrated at Jänschwalde === Australia === The Federal Resources and Energy Minister Martin Ferguson opened the first geosequestration project in the southern hemisphere in April 2008 The demonstration plant is near Nirranda South in South Western Victoria (35.31°S 149.14°E / -35.31; 149.14) The plant is owned by CO2CRC Limited CO2CRC is a non profit research collaboration supported by government and industry The project has stored and monitored over 80,000 tonnes of carbon dioxide-rich gas which was extracted from a natural gas reservoir via a well, compressed and piped 2.25 km to a new well There the gas has been injected into a depleted natural gas reservoir approximately two kilometers below the surface The project has moved to a second stage and is investigating carbon dioxide trapping in a saline aquifer 1500 meters below the surface The Otway Project is a research and demonstration project, focused on comprehensive monitoring and verification.This plant does not propose to capture CO2 from coal-fired power generation, though two CO2CRC demonstration projects at a Victorian power station and research gasifier are demonstrating solvent, membrane, and adsorbent capture technologies from coal combustion Currently, only small-scale projects are storing CO2 stripped from the products of combustion of coal burnt for electricity generation at coal-fired power stations

Work currently being carried out by the GreenMag Group and the University of Newcastle and funded by the New South Wales and Australian Governments and industry intends to have a working mineral carbonation pilot plant in operation by 2013 ==== Gorgon Carbon Dioxide Injection Project ==== The Gorgon Carbon Dioxide Injection Project is part of the Gorgon Project, the world’s largest natural gas project The Gorgon Project, located on Barrow Island in Western Australia, includes a liquefied natural gas (LNG) plant, a domestic gas plant, and a Carbon Dioxide Injection Project The initial carbon dioxide injections were planned to take place by the end of 2017 Once launched, the Gorgon Carbon Dioxide Injection Project will be the world’s largest CO2 injection plant, with an ability to store up to 4 million tons of CO2 per year – approximately 120 million tons over the project’s lifetime, and 40 percent of total Gorgon Project emissions.The project started extracting gas in February 2017, but carbon capture and storage is now not expected to begin until the first half of 2019, requiring a further five million tonnes of CO2 to be released, because: A Chevron report to the State Government released yesterday said start-up checks this year found leaking valves, valves that could corrode and excess water in the pipeline from the LNG plant to the injection wells that could cause the pipeline to corrode === The Planet Venus === Terraforming the planet Venus by removing CO2 from the atmosphere was first scholarly proposed by the astronomer Carl Sagan in 1961, although fictional treatments, such as The Big Rain of The Psychotechnic League by novelist Poul Anderson, preceded it Adjustments to the existing environment of Venus to support human life would require at least three major changes to the planet’s atmosphere: Reducing Venus’s surface temperature of 462 °C (864 °F), eliminating most of the planet’s dense 9.2 MPa (91 atm) carbon dioxide and sulfur dioxide atmosphere via removal or conversion to some other form, and the addition of breathable oxygen to the atmosphere These three changes are closely interrelated, because Venus’s extreme temperature is due to the high pressure of its dense atmosphere, and the greenhouse effect == Limitations of CCS for power stations == Critics say large-scale CCS deployment is unproven and decades away from being commercialized They say that it is risky and expensive and that a better option is renewable energy Some environmental groups have said there is a risk of leakage during the extremely long storage time required, so have compared CCS technology to storing dangerous radioactive waste from nuclear power stations.Another limitation of CCS is its energy penalty – the reduction in overall plant efficiency due to the carbon capturing process It has been estimated that about 60% of the energy penalty originates from the capture process itself, 30% comes from compression of CO2, while the remaining 10% comes from electricity requirements for necessary pumps and fans CCS technology is expected to use between 10 and 40 percent of the energy produced by a power station

When the net energy efficiencies of CCS fossil-fuel power plants and renewable electricity were compared, a 2019 study found CCS plants to be less effective The electrical energy returned on energy invested ratios (EROEI) of both production methods were estimated, accounting for their operational and infrastructural energy costs Renewable electricity production included solar and wind with sufficient energy storage Thus, in climate crisis mitigation, rapid expansion of scalable renewable electricity and storage would be preferable over fossil-fuel CCS.The use of CCS could reduce CO2 emissions from the stacks of coal power plants by 85–90% or more, but it has no effect on CO2 emissions due to the mining and transport of coal It will actually “increase such emissions and of air pollutants per unit of net delivered power and will increase all ecological, land-use, air-pollution, and water-pollution impacts from coal mining, transport, and processing, because the CCS system requires 25% more energy, thus 25% more coal combustion, than does a system without CCS”.On one hand, Greenpeace claims that CCS could lead to a doubling of coal plant costs It is also claimed by opponents to CCS that money spent on CCS will divert investments away from other solutions to climate change On the other hand, BECCS is used in some IPCC scenarios to help meet mitigation targets such as 1.5 degrees C == Use for heavy industry == In some countries, such as the UK, although CCS will be trialled for gas-fired power stations it will also be considered to help with decarbonization of industry and heating == Cost == Although the processes involved in CCS have been demonstrated in other industrial applications, no commercial scale projects which integrate these processes exist; the costs therefore are somewhat uncertain Some recent credible estimates indicate that the cost of capturing and storing carbon dioxide is US$60 per ton, corresponding to an increase in electricity prices of about US 6c per kWh (based on typical coal-fired power plant emissions of 0.97 kg (2.13 lb) CO2 per kWh) This would double the typical US industrial electricity price (now at around 6c per kWh) and increase the typical retail residential electricity price by about 50% (assuming 100% of power is from coal, which may not necessarily be the case, as this varies from state to state) Similar (approximate) price increases would likely be expected in coal dependent countries such as Australia, because the capture technology and chemistry, as well as the transport and injection costs from such power plants would not, in an overall sense, vary significantly from country to country.The reasons that CCS is expected to cause such power price increases are several Firstly, the increased energy requirements of capturing and compressing CO2 significantly raises the operating costs of CCS-equipped power plants In addition, there are added investment and capital costs The process would increase the fuel requirement of a plant with CCS by about 25% for a coal-fired plant, and about 15% for a gas-fired plant

The cost of this extra fuel, as well as storage and other system costs, are estimated to increase the costs of energy from a power plant with CCS by 30–60%, depending on the specific circumstances Pre-commercial CCS demonstration projects are likely to be more expensive than mature CCS technology; the total additional costs of an early large-scale CCS demonstration project are estimated to be €0.5–1.1 billion per project over the project lifetime Other applications are possible In the belief that use of sequestered carbon could be harnessed to offset the cost of capture and storage, Walker Architects published the first CO2 gas CAES application, proposing the use of sequestered CO2 for Energy Storage on October 24, 2008 To date the feasibility of such potential offsets to the cost have not been examined The cost of CCS depends on the cost of capture and storage, which varies according to the method used Geological storage in saline formations or depleted oil or gas fields typically cost US$0.50–8.00 per tonne of CO2 injected, plus an additional US$0.10–0.30 for monitoring costs When storage is combined with enhanced oil recovery to extract extra oil from an oil field, however, the storage could yield net benefits of US$10–16 per tonne of CO2 injected (based on 2003 oil prices) This would likely negate some of the effect of the carbon capture when the oil was burnt as fuel Even taking this into account, as the table above shows, the benefits do not outweigh the extra costs of capture.Cost of electricity generated by different sources including those incorporating CCS technologies can be found in cost of electricity by source If CO2 capture was part of a fuel cycle then the CO2 would have value rather than be a cost The proposed Solar Fuel or methane cycle proposed by the Fraunhofer Society amongst others is an example This “solar fuel” cycle uses the excess electrical renewable energy to create hydrogen via electrolysis of water The hydrogen is then combined with CO2 to create synthetic natural gas SNG and stored in the gas network See the latest Cost Report on the Cost of CO2 Capture produced by the Zero Emissions Platform Governments around the world have provided a range of different types of funding support to CCS demonstration projects, including tax credits, allocations and grants The funding is associated with both a desire to accelerate innovation activities for CCS as a low-carbon technology and the need for economic stimulus activities As of 2011, approximately US$23.5bn has been made available to support large-scale CCS demonstration projects around the world === Carbon capture and storage and the Kyoto Protocol === One way to finance future CCS projects could be through the Clean Development Mechanism of the Kyoto Protocol At COP16 in 2010, The Subsidiary Body for Scientific and Technological Advice, at its thirty-third session, issued a draft document recommending the inclusion of Carbon dioxide capture and storage in geological formations in Clean Development Mechanism project activities At COP17 in Durban, a final agreement was reached enabling CCS projects to receive support

through the Clean Development Mechanism == Environmental effects == === Fossil Fuel Power Plants === The theoretical merit of CCS systems is the reduction of CO2 emissions by up to 90%, depending on plant type Generally, environmental effects from use of CCS arise during power production, CO2 capture, transport, and storage Issues relating to storage are discussed in those sections Additional energy is required for CO2 capture, and this means that substantially more fuel has to be used to produce the same amount of power, depending on the plant type For new super-critical pulverized coal (PC) plants using current technology, the extra energy requirements range from 24 to 40%, while for natural gas combined cycle (NGCC) plants the range is 11–22% and for coal-based gasification combined cycle (IGCC) systems it is 14–25% [IPCC, 2005] Obviously, fuel use and environmental problems arising from mining and extraction of coal or gas increase accordingly Plants equipped with flue-gas desulfurization (FGD) systems for sulfur dioxide control require proportionally greater amounts of limestone, and systems equipped with selective catalytic reduction systems for nitrogen oxides produced during combustion require proportionally greater amounts of ammonia IPCC has provided estimates of air emissions from various CCS plant designs (see table below) While CO2 is drastically reduced though never completely captured, emissions of air pollutants increase significantly, generally due to the energy penalty of capture Hence, the use of CCS entails a reduction in air quality Type and amount of air pollutants still depends on technology CO2 is captured with alkaline solvents catching the acidic CO2 at low temperatures in the absorber and releasing CO2 at higher temperatures in a desorber Chilled Ammonia CCS Plants have inevitable ammonia emissions to air “Functionalized Ammonia” emit less ammonia, but amines may form secondary amines and these will emit volatile nitrosamines by a side reaction with nitrogendioxide, which is present in any flue gas even after DeNOx Nevertheless, there are advanced amines in testing with little to no vapor pressure to avoid these amine- and consecutive nitrosamine emissions Nevertheless, all the capture plants amines have in common, that practically 100% of remaining sulfur dioxide from the plant is washed out of the flue gas, the same applies to dust/ash == See also

You Want To Have Your Favorite Car?

We have a big list of modern & classic cars in both used and new categories.